No. of sale: 130526M
Starting date
ManufacturerChiron ModelFZ 08K S Magnum SK Year2007 - 2017 ObservationsCNC Vertical Machining Center - 5 Axes
General overhaul: refurbishment in 2017
Operating hours: approx. 22,500 h
Equipped with NC swiveling head, rotary table, bar feeder and automatic unloading system.
CNC Control System
CNC Control: Siemens 840D
NC tilting head
·Swivel range: -20° / +115°
Main Spindle
Type: Water-cooled motor spindle
Maximum speed: 15,000 rpm
Travels
·X-axis: 450 mm
·Y-axis: 270 mm
·Z-axis: 310 mm
Speeds
·Rapid traverse: X / Y / Z: 75 m/min
Tool Changer
·Number of tools: 40 positions
·Tool interface: HSK-A40
·Tool-to-tool change time: 2.6 seconds (vertical)
Additional Equipment
·Preparation for bar machining
·AWU 160 rotary table
·Rotary table diameter: 105 mm
·Additional positioning axis
·Hainbuch Spanntop D100 collet chuck
·Additional device for sixth-face machining
·Automatic finished parts extraction and unloading system
·IRCO SiMag 100.1-3000 bar feeder for round and profiled material
·Washing gun
·Preparation for internal tool cooling (IKZ)
·70 bar high-pressure coolant system with Varioventil valve
·Device washing system
·Scraper-type chip conveyor
·Chip discharge height: 1050 mm
·Vacuum rotary filter VRF 400 liters, manufacturer KNOLL
·MAHLE switchable double filter
·Electrical cabinet cooler
·Signal light tower
·Tool life monitoring
·Single F500 tool breakage monitoring
·Renishaw TS27R 3D probing system
·Brankamp Marposs CMS 100 collision monitoring system
Included Accessories
·Breuning IRCO guide channel sets
·Hainbuch collets (as agreed)
·Approximately 500 HSK-A40 tool holders
·Spare parts for this machine type
·Machine-specific consumables
Production Concept
The system is designed for fully automated 24/7 unmanned production of cubic parts.
Material is fed via a bar feeder with capacity for bars up to 100 mm diameter and 3000 mm length, suitable for both round and profiled material.
The rotary table acts as a positioning axis, allowing machining of the four lateral faces using the vertical milling spindle.
The fifth face is machined horizontally using the tilting head.
Afterwards, the part is cut off, rotated 180°, and the sixth face is machined using the tilting head.
Finished parts are automatically removed by a handling system and deposited in a parts storage unit.
Machine Condition
·Factory overhaul carried out in 2017
·Last spindle replacement: September 2025
·Last full annual maintenance: October 2025
·The machine has been continuously maintained by the manufacturer under a full service contract, including preventive maintenance and technical upgrades.
ManufacturerChiron ModelFZ 08K S Magnum SK Year2007 - 2017 ObservationsCNC Vertical Machining Center - 5 Axes
General overhaul: refurbishment in 2017
Operating hours: approx. 22,500 h
Equipped with NC swiveling head, rotary table, bar feeder and automatic unloading system.
CNC Control System
CNC Control: Siemens 840D
NC tilting head
·Swivel range: -20° / +115°
Main Spindle
Type: Water-cooled motor spindle
Maximum speed: 15,000 rpm
Travels
·X-axis: 450 mm
·Y-axis: 270 mm
·Z-axis: 310 mm
Speeds
·Rapid traverse: X / Y / Z: 75 m/min
Tool Changer
·Number of tools: 40 positions
·Tool interface: HSK-A40
·Tool-to-tool change time: 2.6 seconds (vertical)
Additional Equipment
·Preparation for bar machining
·AWU 160 rotary table
·Rotary table diameter: 105 mm
·Additional positioning axis
·Hainbuch Spanntop D100 collet chuck
·Additional device for sixth-face machining
·Automatic finished parts extraction and unloading system
·IRCO SiMag 100.1-3000 bar feeder for round and profiled material
·Washing gun
·Preparation for internal tool cooling (IKZ)
·70 bar high-pressure coolant system with Varioventil valve
·Device washing system
·Scraper-type chip conveyor
·Chip discharge height: 1050 mm
·Vacuum rotary filter VRF 400 liters, manufacturer KNOLL
·MAHLE switchable double filter
·Electrical cabinet cooler
·Signal light tower
·Tool life monitoring
·Single F500 tool breakage monitoring
·Renishaw TS27R 3D probing system
·Brankamp Marposs CMS 100 collision monitoring system
Included Accessories
·Breuning IRCO guide channel sets
·Hainbuch collets (as agreed)
·Approximately 500 HSK-A40 tool holders
·Spare parts for this machine type
·Machine-specific consumables
Production Concept
The system is designed for fully automated 24/7 unmanned production of cubic parts.
Material is fed via a bar feeder with capacity for bars up to 100 mm diameter and 3000 mm length, suitable for both round and profiled material.
The rotary table acts as a positioning axis, allowing machining of the four lateral faces using the vertical milling spindle.
The fifth face is machined horizontally using the tilting head.
Afterwards, the part is cut off, rotated 180°, and the sixth face is machined using the tilting head.
Finished parts are automatically removed by a handling system and deposited in a parts storage unit.
Machine Condition
·Factory overhaul carried out in 2017
·Last spindle replacement: September 2025
·Last full annual maintenance: October 2025
·The machine has been continuously maintained by the manufacturer under a full service contract, including preventive maintenance and technical upgrades.
Start price 59.500 €
ManufacturerTRAUB ModelTNK 36 Year2003 ObservationsCNC Turning Center
Operating Hours: Approx. 124,705 h (May 2026)
Machine Description
The TRAUB TNK 36 is a high-performance CNC turning center designed for automated production of precision components from bar stock. Equipped with a main spindle, counter spindle, C-axis capability, driven tools, high-pressure coolant system, and automatic bar feeder, the machine is suitable for unattended operation and medium-to-high volume production.
CNC Control System
·TRAUB TX8i CNC Control (64-bit)
·10.4" Flat Screen Display
·Additional V24 RS232 Interface
·MDE Production Monitoring Interface
·Tool Monitoring System
·Rigid Tapping without Compensation Chuck
Main Spindle
·Bar Capacity: Ø 36 mm
·Maximum Spindle Speed: 6,300 rpm
·Drive Power:
o6.7 kW (Continuous)
o10.7 kW (Peak)
·Integrated C-Axis
·Hainbuch Quick-Change Clamping System
·Manual Hainbuch Changeover Device Included
Counter Spindle
·Motorized Counter Spindle
·Integrated C-Axis
·Counter Clamping Pressure Device
·Automatic Workpiece Ejector
·Hainbuch Axfix Chuck System
Tooling System
Upper Tool Carrier
·Driven Tool Capability
·Electronic Gear Function
·X3 Cross Axis for Front Working Unit
Front Working Unit
·5 Tool Positions
·Driven Tool Capability
Cut-Off / Back Working Station
·Driven Tool Capability for Secondary Operations
Workpiece Handling
·Automatic Part Gripper
·Gripper Jaw Sets Included:
oØ 5-8 mm
oØ 8-20 mm
oØ 20-36 mm
Coolant System
Standard Coolant Unit
·Tank Capacity: 230 Litres
·Pressure: 7 bar
·Flow Rate: 50 l/min
Through-Tool Coolant
·Internal Coolant Supply: 30 bar
·High-Pressure Coolant:
o120 bar at Front Working Station
o120 bar at Rear Working Station
Filtration
·KNOLL VRF 150/750 Vacuum Rotary Filter
·Suitable for:
oAluminium
oBrass
oSteel
oPlastics
·Coolant Cleaning Gun Included
Additional Equipment
·Hinged-Belt Chip Conveyor
·Discharge Height: 950 mm
·Preparation for Automatic Bar Loader
·Guide Tubes for Ø25 mm and Ø36 mm Bars
·Synchronous Workpiece Stop
·Brankamp CMS 100 Collision Monitoring System on Main and Counter Spindle
Bar Feeding System
Manufacturer: FMB
Model: Turbo 5-42 XT / 3200 C
Year: 2003
Capacity
·Maximum Bar Length: 3,000 mm
·Maximum Bar Diameter: Ø36 mm
·Designed for Fully Automatic Unattended Production
Electrical Data
·Connected Load: 22 kW
·Supply Voltage: 400 V
·Frequency: 50 Hz
·Rated Current: 60 A
Included Accessories
·Basic Set of Static Tool Holders
·Basic Set of Driven Tool Holders
·Hainbuch Clamping Equipment
·Workpiece Gripper Sets
·Chip Conveyor
·Coolant System
·FMB Bar Feeder
Machine Condition
·No known defects reported by the owner.
·Machine remained in productive operation until May 2026.
·Operated in a 2.5-shift production environment.
·Currently decommissioned but remains electrically connected.
·Available for inspection and power-on demonstration.
Main Advantages
✔ Main spindle and counter spindle with C-axis capability
✔ Driven tooling for milling, drilling and tapping operations
✔ High-pressure coolant system up to 120 bar
✔ Automatic FMB bar feeder for lights-out manufacturing
✔ Tool monitoring and collision detection system
✔ Suitable for steel, aluminium, brass and plastic machining
✔ High productivity for medium and large batch production
✔ Proven TRAUB reliability and precision engineering
ManufacturerTRAUB ModelTNK 36 Year2003 ObservationsCNC Turning Center
Operating Hours: Approx. 124,705 h (May 2026)
Machine Description
The TRAUB TNK 36 is a high-performance CNC turning center designed for automated production of precision components from bar stock. Equipped with a main spindle, counter spindle, C-axis capability, driven tools, high-pressure coolant system, and automatic bar feeder, the machine is suitable for unattended operation and medium-to-high volume production.
CNC Control System
·TRAUB TX8i CNC Control (64-bit)
·10.4" Flat Screen Display
·Additional V24 RS232 Interface
·MDE Production Monitoring Interface
·Tool Monitoring System
·Rigid Tapping without Compensation Chuck
Main Spindle
·Bar Capacity: Ø 36 mm
·Maximum Spindle Speed: 6,300 rpm
·Drive Power:
o6.7 kW (Continuous)
o10.7 kW (Peak)
·Integrated C-Axis
·Hainbuch Quick-Change Clamping System
·Manual Hainbuch Changeover Device Included
Counter Spindle
·Motorized Counter Spindle
·Integrated C-Axis
·Counter Clamping Pressure Device
·Automatic Workpiece Ejector
·Hainbuch Axfix Chuck System
Tooling System
Upper Tool Carrier
·Driven Tool Capability
·Electronic Gear Function
·X3 Cross Axis for Front Working Unit
Front Working Unit
·5 Tool Positions
·Driven Tool Capability
Cut-Off / Back Working Station
·Driven Tool Capability for Secondary Operations
Workpiece Handling
·Automatic Part Gripper
·Gripper Jaw Sets Included:
oØ 5-8 mm
oØ 8-20 mm
oØ 20-36 mm
Coolant System
Standard Coolant Unit
·Tank Capacity: 230 Litres
·Pressure: 7 bar
·Flow Rate: 50 l/min
Through-Tool Coolant
·Internal Coolant Supply: 30 bar
·High-Pressure Coolant:
o120 bar at Front Working Station
o120 bar at Rear Working Station
Filtration
·KNOLL VRF 150/750 Vacuum Rotary Filter
·Suitable for:
oAluminium
oBrass
oSteel
oPlastics
·Coolant Cleaning Gun Included
Additional Equipment
·Hinged-Belt Chip Conveyor
·Discharge Height: 950 mm
·Preparation for Automatic Bar Loader
·Guide Tubes for Ø25 mm and Ø36 mm Bars
·Synchronous Workpiece Stop
·Brankamp CMS 100 Collision Monitoring System on Main and Counter Spindle
Bar Feeding System
Manufacturer: FMB
Model: Turbo 5-42 XT / 3200 C
Year: 2003
Capacity
·Maximum Bar Length: 3,000 mm
·Maximum Bar Diameter: Ø36 mm
·Designed for Fully Automatic Unattended Production
Electrical Data
·Connected Load: 22 kW
·Supply Voltage: 400 V
·Frequency: 50 Hz
·Rated Current: 60 A
Included Accessories
·Basic Set of Static Tool Holders
·Basic Set of Driven Tool Holders
·Hainbuch Clamping Equipment
·Workpiece Gripper Sets
·Chip Conveyor
·Coolant System
·FMB Bar Feeder
Machine Condition
·No known defects reported by the owner.
·Machine remained in productive operation until May 2026.
·Operated in a 2.5-shift production environment.
·Currently decommissioned but remains electrically connected.
·Available for inspection and power-on demonstration.
Main Advantages
✔ Main spindle and counter spindle with C-axis capability
✔ Driven tooling for milling, drilling and tapping operations
✔ High-pressure coolant system up to 120 bar
✔ Automatic FMB bar feeder for lights-out manufacturing
✔ Tool monitoring and collision detection system
✔ Suitable for steel, aluminium, brass and plastic machining
✔ High productivity for medium and large batch production
✔ Proven TRAUB reliability and precision engineering
Start price 45.000 €
